[79FT]: Building Things

Tagged with "wheels":

Brakes and Wheels

fixin' and bleedin'


On: Nov 04, 2019
In: [Chickenhouse Charger] Electrical Rebuild
Time logged: 23.1
Tags: 6781G, MA5 Charger, Annual, brakes, wheels

So this one turned into a month long project, give or take. Sure, sure, I was doing other things, too: last one of which was completed October 9th... after which I was finishing this one exclusively, pretty much.

Damn. One month to finish putting the brakes together. Granted, I had a hiatus for a week and a half, dealing with fixing up bad (non-aircraft) plumbing and cutting (non-aircraft-grade) trees.

Regardless... Shall we?

...

After having finished making the new brake line, I naturally wanted to install it and call brakes done.

Some of the disassembly work documented here actually happened prior to the new line being bent up, but hey. Putting it all in one place makes for a better narrative in one context.

First, the Calipers

... one of which was cracked due to someone having overtightened the bleeder adapter. Oh well.

Drain

Drain

... and pull

... and pull

Brake pads were soaked in brake fluid. For that matter, the disk was covered in brake fluid that hardened to molasses-like consistency (which mineral milspec fluid does, apparently).

Ugly smudge

Ugly smudge

Intermission. By the way, it seems that this smudge didn't come from the dripping bleeder, but rather, judging by how the pads were soaked, from under the brake piston. Probably the o-ring was bust, and it was weeping from between the caliper and the piston. It seems that it had been a feature of the plane for a while.

Jumping a bit ahead of myself, on the other side, I discovered the brake disk somewhat dirty with oil - crankcase breather hoses are routed into the _left_ side wheelpant and terminate near the disk - clearly, spraying a bit of oil on and around it. You'll see those hoses on the pics of the left wheel below.

I think Remo's idea was to prevent oil on the belly from the breather. My friend's Ben contention was, this was a brake lock-up prevention measure; and when he brought it up, I immediately realized... leaking piston on the _right_ caliper was a lock-up prevention measure as well - to make sure both brakes are equally slippery - right one with brake fluid, left one with motor oil... At any rate,..

I will admit, this was my first caliper job ever, and anchor pins presented a bit of a problem. They're press fit in the caliper, and I didn't have an arbor press. Well, I used an old 1/4 nut that I banged on (gently!), and finished with a drift punch....

Tappy-tap-tap!

Tapping out the pins (aka anchor bolts)

Tapping out the pins (aka anchor bolts)

With the caliper put apart, I tossed the old body, and took maroon scotch-brite to the rest of the pieces to clean them up.

Cleaning up the parts

Cleaning up the parts

Now, I tried tapping the anchor pins back in, but was too afraid to mess them up. Finally, that was an excuse to go get me an arbor press!

Pressing the pins back in

Pressing the pins back in

One final bit was to put the nuts back on.

Ready for nuts

Ready for nuts

Question: how many wrenches does it take to put on an aircraft grade nut properly? Answer: three.

Wrenches!

Wrenches!

Answer: three. Ratchet to work the nut before it's torqued. Small torque wrench to determine the free torque. Large torque wrench to torque to spec.

I pulled off the other caliper, and cleaned it up, too.

Left caliper, cleaned

Left caliper, cleaned

Put in new piston o-rings, cleaned up AN flare adapters, put the calipers back together, and put them away.

Next step was,

The Parking Brake Valve

That little doodad was leaking for a long time, too. It seemed it was leaking from the little cam arm that rotates, but I wasn't sure, so I decided to put it apart and rebuild it completely, too.

It's under the passenger's seat on the Charger.

Pulled it off

Pulled it off

On the bench

On the bench

First, I pulled the "cam arm" out - the little arm pivots, and pushes valves open (or lets them close) inside the box.

Cam actuating arm

Cam actuating arm

O-rings were in reasonable shape, but looked a bit.. old. I decided to change them and disassemble the rest of the contraption, to change all the other o-rings in it.

Now, the middle two "straight" fittings are straight threads and o-rings under them. No problems there.

The two 90 degree elbows on the sides are NPT. One came out just fine. The other... Well, the other decided to leave a chunk of itself inside the valve body...

Bits and pieces - valves, springs, and actuator plungers

Bits and pieces - valves, springs, and actuator plungers

Busted elbow

Busted elbow

You can see the chunk of the male thread galled and stuck in the female NPT hole of the body.

Chunk of thread

Chunk of thread

Damn damn damn! I need a new parking brake valve now?

That new valve is how much (search.. search.. six hundred and sixty five!?!?!?!?! $#*@(&(2@@#!). No way I'm paying that.

There are alternatives. Cheapest one is like what, hundred fifty bucks; and I'll have to work around it's plumbing (which is different than mine); and the "direct fit" "homebuilt" cheapest one is over $300? No way. No way in hell until I try to fix this.

What is the hole? 1/8 NPT? McMaster sells taps for $25, two new fittings are what... under $30, and a handful of o-rings, which of course I didn't have (I have a bunch of o-rings in a ton of sizes for fuel applications, but not for brake applications).

We'll try to re-tap that hole; hopefully braking the piece of the thread left in there by the fitting while keeping the female thread intact...

... the tap and the o-rings got delivered a few days later. Made myself some nice soft jaws for the vice to hold the thing without scratching it.

Soft jaws

Soft jaws

That's aluminum angle and leather.

Weapons ready!

Weapons ready!

Tap, tap, tap (not that kind of tap!)

Tap, tap, tap (not that kind of tap!)

Slowly, slowly and gently, breaking the chip every 1/4 turn and adding cutting fluid. It worked out great! The hole was deeper than needed, so I tapped the threads a bit deeper, arguing that if the female portion of the threads got chewed up a bit, I'd put a fresh surface on them too.

Done!

Done!

Well, we'll have to wait to see how well this works out. If it doesn't leak, I just saved me a boat-ton of money.

Putting it back together

Putting it back together

All done

All done

New o-rings, new elbow fittings, re-tapped hole. Threads on the busted hole felt good, no hesitation and "catching". We'll see how that works out...

Next,

The Pads

Pads on the right brake (the one with leaking piston o-ring and busted caliper) were soaked in brake fluid. Cleveland says contaminated pads are a cause for replacement, so I decided to do it, since I was already in there. Besides, excuse for another tool - this time, the brake rivet set!

Punching old rivets out

Punching old rivets out

... and putting new ones in

... and putting new ones in

And with that, the last bit before we could put everything back together was,

The Wheels

Again, since I was already there, I decided to do the wheels at this time too - re-pack the bearings, that is, and give the disk contaminated with brake fluid a real good cleaning.

Jacking the plane

Jacking the plane

The axle nut comes off with finger pressure

The axle nut comes off with finger pressure

I admit - I made a mistake here. I did not remember what kind of resistance I felt when spinning the wheel on the axle before I took off the nut and took everything apart. It would've been important, especially since this was my first time doing these wheels, and wheels in general....

Temp

Temp "wheel"

Cleaning bearings

Cleaning bearings

All the grease seals (and bearings)

All the grease seals (and bearings)

Crap! What, the felt seal is bust!?.. Looks like it is. Okay, not finishing this part quickly (because of yet again, another "order parts / wait" cycle).

Flushed, and drying

Flushed, and drying

Do you see the other mistake I made? Yep. I mixed up the bearings ("front" and "back"). Bearings should always stay with their races...

Oh well. After some research, seems that the worst that will happen is wear will get accelerated.. since the bearings and races looked squeaky clean, I decided to keep them as is.. for now. And just Hail Mary the position (since I have a 50% chance of getting it right :)).

I decided to replace all the felts because I was changing grease from I didn't know what kind but likely red Mobil grease to Aeroshell 22.

Ironically, I apparently didn't take a single picture of the bearings being greased - probably because my hands were too greasy doing them :). Oh well.

The new felts came, and got coated in grease.

One of new felts

One of new felts

And, I put the wheel back together. And then... And then, I couldn't tighten it back right. I have to align the hole in the axle nut for the cotter pin... I could either get it under-tight (with perceptible play in the bearings - not good), or a bit over-tight (so that the wheel will spin, but with some measure of resistance). Remember, I said that my mistake number one was not checking how freely this wheel spun prior to pulling it off? Now, I was paying for it.

I tried flipping the bearings around (because I didn't note their original positions), thinking that maybe that will help. Nope. No change at all.

Oh well. I couldn't do anything about that at that point, so decided to settle on "a bit tighter" option.

Cotter pin

Cotter pin

With the other wheel, things went much smoother (the second time you do the job, it takes you 10% of time it took you to do it the first time, right? :) ). It came off, was cleaned, and got back on, with new felts and bearings in the original positions. Nut got tightened to super tight, loosened, and tightened to finger tight - and the wheel was perfect. No play, and no "drag".

Le double sigh.

So finally, it was the time to put things back together!

Putting the Brakes Back On

That was almost pleasant, after all the mess-aroundary with bearings. I cleaned up the pins' glide bushings, and lubed them with Dri-Slide (graphite + moly) lube Parker recommends.

And then... Calipers on, slide the bolts in, torque.

Putting calipers back on

Putting calipers back on

Even a child could do it! By the way, that's the left wheel - remember I was mentioning the breather hoses routed to that wheel? There they are, in their awesome oil-spraying glory...

Parking brake back on

Parking brake back on

Put the parking brake back on.

Phew. Now, finally, we can bleed and test!

Bleeding

Now, there are two approaches to bleeding brakes - either bottom up (push fluid up thru the bleeder valves), or top down (sit in the plane and squeeze the pedals while the other guy opens and closes the bleeder). Bottom up is inherently simpler.

Some time ago, my buddy Dick was showing off his fancy bleeder he got from ATS.

ATS Brake bleeder

ATS Brake bleeder

Hmmm.. What is that reminding me of? Aha! Bug sprayer! That's right

Bug sprayer

Bug sprayer

Now, a few minor modifications, and...

DIY brake bleeder

DIY brake bleeder

Pump it with air, open the valve, and the brake fluid gets pushed out thru the line that attaches to the bleeder valve on the caliper. Child's play.

For bleeding, I dragged my good friend Nick S. to give me a helping hand. I could've done this by myself, but having someone watching over the "other end" (it either being the end that pushes the fluid in, or the end out of which the fluid comes out) makes the job much more pleasant.

Now, the way brakes are plumbed on the Charger is, each side goes from it's caliper up the gear leg to the parking brake valve, then to the Master Cylinder, and from there both Master Cylinders are plumbed into a tee, from which the single line (the one I was re-making earlier) goes to the reservoir on the firewall.

We decided to bleed each side up to the tee first - to minimize the amount of air ending in the "common" line between the tee and the firewall. After bleeding each side up to the tee, we'd attach the "common" line and bleed each side up to the reservoir, letting at least a cup of fluid to flow thru, ensuring that we push all the air out.

The setup

The setup

The plan went without a hitch, aside from the fact that I initially forgot to open the parking brake, and was trying to figure out why the hell the fluid won't flow. Hehe. Nick called it, too!

Nick holding the fluid line from reservoir

Nick holding the fluid line from reservoir

Finally, the moment of truth. The brakes were firm and nice, held well, and no leaks nowhere! Now, I need to double-check this - next time I'm in the hangar for a good few hours, I'll set the parking brake to keep the pressure in lines, and see what happens - but initially, everything held just fine! Phew.

So finally, the last bit was left.

Finishing the New Line Install

Now, the new line was finally in place, and all that was left was to install some ADELs to hold it.

ADEL One

ADEL One

That one took ... an hour! Very nasty spot and hard to get to. I had to find a better way...

Now, there are fancy mods to ViceGrips (or you can buy them for sizeable chunks of cash pre-made) to hold ADEL clamps together while you're inserting the screw and starting the nut. I don't have them.

Some people use safety wire.

I decided to try...

Lacing cord!

Lacing cord!

It works great, too! Just double up and "noose" it around - it holds a clamp like a charm in the "closed" position while you fiddle with the nut! Even Jack came out to see that.

Jack inspecting the work

Jack inspecting the work

With those clamps installed, I had to tie a bundle of wires going across the tube to the front stick's PTT switch. That one was one hell of a contortion exercise, under the front seat's front edge and behind the stick, but I managed after a couple of tries.

Lacing the wires to brake fluid line and structure

Lacing the wires to brake fluid line and structure

And finally, a couple more clamps along the length of the line on the fuse to hold it in place there. Some TorqSeal, and we're done!

I worked out a method to these, finally, I think. I use a long (~2 inches) AN3 bolt first to "thread" the clamps on, and then close them with a wrap of lacing cord using the "noose" method ("Method 2" here). I then remove the long bolt, install the final bolt, and start the nut. When the nut brings clamps almost to a close, I cut off the nooses, and tighten the nut. Works like a charm!

All done!

All done!

So, there. A pretty big job now complete - brake system rebuilt, re-bled, and ready to go.

PS: I was considering where to put this - under "2019 Annual" or "Electrical Rebuild" category... decided to pile it into the "Electrical Rebuild", because basically as a part of this rebuild I'm doing a bunch more stuff.. This is basically becoming a "minor restore" project... But still, the main theme is "Electrical Rebuild", and I'm keeping it under this section.


"Climb like you're life depends on it ... because it does."
-ORD ATC



Powered by B-Log, which is based on Pelican, heavily plugged and themed.

© Copyright "79FT". All rights reserved. Feel free to cite, but link back to the pages cited.

This website only shows how I did things in my various projects. These pages are for information and personal entertainment only and not to be construed as the only way, or even the perceived correct way of doing things. You are responsible for your own safety and techniques.