[79FT]: Building Things

Annual 2019: The Rest of April

...and 1/2 of May


On: May 14, 2019
In: [Chickenhouse Charger] 2019 Annual
Tags: 6781G, MA5 Charger, Annual, Rotec TBI, baffles, prop, fabric

Well, as usual, I got too focused on the plane and the mess I got myself into; and didn't log things as they went...

I will split the notes in multiple posts; by theme / subject. Just general notes here.

Annual, Continued

We got together with John, my IA, and continued working on the plane early April.

We pulled the prop, so that I will have access to baffles (I wanted to redo them).

John re-riveted the air takeoff flange back to the front ramp.

Meanwhile, I started disassembling the fuel system to get to the screens, including the oil sump screen, and clean them.

Airbox off

Airbox off

TBI intake airflow straightener

TBI intake airflow straightener

Okay, stop right there. See that fuel inlet, right above the air intake? See the little smudge of dope around the inlet fitting? Yep. Teflon dope. Rotec explicitly tells you not to put ANYTHING on there - there's a copper crush gasket behind that fitting.

TBI screen

TBI screen

TBI crush gasket

TBI crush gasket

See all that dope above? Okay, that thread on the TBI is a female thread. Dope will be all in it, and guess what will happen when I screw the fitting back in? Yep. It'll go into the TBI fuel galleys. Right to where that spray bar is with tiny little holes in it. Not Good (c).

TBI holes plugged

TBI holes plugged

Intakes

I noticed evidence of possible intake leaks, so without "burping" the engine, decided to pull the intakes and replace the gaskets. This is my karma. I did that on the Cheetah just a year ago, and scraping remnants of one of those gaskets and re-chasing the threads took me about 10 hours; maybe more.

Also: interesting note: she has intake tube clamps on studs and not bolts like every other Lycoming I've seen. Old, narrow-deck cylinders :).

Prop

When we pulled it, bolts were in the thru holes on the wooden prop really tight.

Pulling the prop

Pulling the prop

She has the prop made by Frank Johnson of Performance Propellers fame, and after contacting him, he just suggested to re-drill the holes and re-coat them inside with something.

Well, I got me a 29/64 (1/64 oversize) reamer, and went to town.

But first, I needed a rack.

My prop rack

My prop rack

Built with a 1/2" pipe, some foam, pipe brackets, screws, 2x6s screwed to the table, and my 3/8" drive extension rod. You get the idea :). Redneck engineering galore.

Prop on the rack

Prop on the rack

This whole thing was happening over a few days by the way; and when I finally got my reamer and had time to deal with it, the holes.. extended. Wood moves!

Hey, we had much rain then, and prop "swelled" a bit methinks.

But I still decided to fill the holes as much as I could.

Even got me some nice scales for mixing System Three ClearCoat.

Mixing

Mixing

A filled hole

A filled hole

Backside

Backside

Interlude

Hey, look, I got a nice neighbor next door!

My new neighbor

My new neighbor

Fabric

Fabric on this plane is old. Flyable from what I am being told by experts, but old. Cracking, peeling paint.

Original logs say that she was covered in Polyfiber. But the current finish looks more like Imron and the company - "flexible" automotive poly. It's cracking and peeling around areas of high wear (prop wash, etc).

Sad fabric

Sad fabric

Sad, sad fabric

Sad, sad fabric

John (my IA) wanted to take a Maule fabric tester to it; but I didn't want holes in my wings.

I discussed this with a few guys that worked with fabric their whole lives, and we came to a consensus that for now this is fine. Will just fill with silver, and keep on flying. Incidentally, that's what Glenn has been doing, too.

Full Stop

I worked on baffles a bit, but then, everything went downhill. We'll talk about baffles in the next post. And the downhill part, afterwards :).


"Hey, O'Hare, you see the 7600 code flashing five northwest of Gary?"
"Yeah, I do...you guys talkin' to him?"
-ORD ATC


Up ↑

Powered by B-Log, which is based on Pelican, heavily plugged and themed.

© Copyright "79FT". All rights reserved. Feel free to cite, but link back to the pages cited.

This website only shows how I did things in my various projects. These pages are for information and personal entertainment only and not to be construed as the only way, or even the perceived correct way of doing things. You are responsible for your own safety and techniques.